Four different material bathtub maintenance tips-bathroom common sense, bathtub maintenance

The acrylic plastic bathtub is light in weight, does not rust, will not be corroded, feels warm to the touch, can maintain the water temperature for a long time, and is easy to wipe clean. This bathtub is currently the mainstream product on the market. When maintaining the bathtub, you can choose a suitable polishing machine, use the wool polishing disc of the 1900 rpm model, apply wax on the polishing disc, and then polish the polishing part. Before sanding, the surface should be repaired with sandpaper (No. 1000 or No. 1500), repeated many times, and finally a bright surface is achieved. The polishing wax is made of high-quality products. Car polishing wax can be used. For small scratches or worn out areas, manual polishing can be used: first polish it with 1500 water-resistant paper, and then use the car surface abrasive to repeatedly rotate in circles to make the surface bright and even Toothpaste can be used instead of abrasive, but the grinding time is relatively much longer. The surface of the reliable brand acrylic bathtub is specially treated, which is stronger than the general acrylic bathtub. In case of accidental scratches on the surface, if the scratches are light, you can use toothpaste and a toothbrush to brush lightly; if the scratches are deep, it is recommended to seek professional advice and professional maintenance personnel to deal with it. You can use turpentine water to clean the paint gelatin stained on the bathtub. Many chemicals will cause the acrylic to lose its luster, such as Tianna water. Usually, you only need to use No. 1 cleaner to clean it, do not use corrosive cleaners. Cast iron bathtubs are a very heavy and good material. The enamel on the surface is generally thinner than that of steel bathtubs. When cleaning such bathtubs, abrasive cleaners should not be used. The disadvantage of such bathtubs is that the water can quickly become cold. , Cast iron bathtubs are usually bulky (except for tens of thousands of high-end products), expensive, and the heat preservation is not very good. But its advantage is long service life. The bathtub can be cleaned with a non-acidic detergent, and a non-abrasive soft sponge pad can be used to clean the difficult-to-remove dirt on the non-slip surface of the bathtub. Cast iron bathtubs are more prone to scratches. If there are rusty scratches, first remove the rust spots with decontamination powder, then wipe with a dry cloth, and then apply a special adhesive for repairing the bathtub, so that the scratches will not expand. When cleaning the bathtub, you must use a sponge and washing powder to clean it, not a hard brush. When the barrels leave the factory, they will be coated with a layer of tung oil, so in the first few days of purchase, make sure to keep the air in the bathroom and open the windows regularly for ventilation, so as to avoid the pungent smell in the home. Water seepage will appear in the initial water test, which is a normal phenomenon. After the water is full, it should be soaked for more than 12 hours to fully infiltrate the wooden barrel, and the seepage of the wooden barrel will stop. If there is any problem, you should contact the manufacturer in time. Because the wood itself will expand and contract with heat, it should not be directly exposed to the sun or blown by the cold wind. If it is not used for more than two months for a long time, the wooden barrel can be wet and sealed with a large plastic bag to prevent the air from taking away the moisture. It is best to put a little water when not in use, so that it can absorb water and keep the wood saturated and moist, but do not use too much water, because the bathroom itself has a certain humidity. Pay attention not to use the dirty water after bathing, so as not to absorb the sewage and accelerate the aging or produce mildew. Bathtub maintenance tips of four different materials in bathroom design After the barrel is used for a period of time, the fixed iron wire outside the barrel will be a little loose. At this time, the barrel can be turned upside down, then the iron wire can be tightened, and hot water can be added to continue to use. There will be differences in the thickness of the wood of the barrel wall. Generally, a barrel with a thickness of 2 cm to 3 cm is selected, and the thermal insulation effect is better. Tips for bathtub maintenance: 1. Clean the bathtub every week to ensure that the bathtub is kept dry after each use. 2. To clean the bathtub, use a neutral liquid detergent and use a soft cloth or a good sponge. 3. Do not use abrasive and highly alkaline cleaning products. 4. Avoid using dark detergents, as it is easy to cause pigments to penetrate into the cylinder surface. 5. After using the water hose, don't forget to turn off the water system, so as to avoid frequent dripping water and cause the bathtub to accumulate water. 6. If there is any damage to the bathtub, you should immediately notify the relevant company to repair it to prevent the problem from worsening. 7. Do not leave metal objects in the bathtub, they will make the bathtub rust and stain the surface.